	// Sample sketch for operating the stepping motor 28BYJ-48 and motor driver UKN2003A using the Arduino standard library
	#include <Stepper.h>
	#define PIN_BLUE 4
	#define PIN_PINK 5
	#define PIN_YELLOW 6
	#define PIN_ORANGE 7
	#define MOTOR_STEPS (2048)
	Stepper stepper(MOTOR_STEPS, PIN_BLUE, PIN_YELLOW, PIN_PINK, PIN_ORANGE);

	void setup() {
	stepper.setSpeed(10);
	}

	void loop() {
	// Rotate the motor 90 degrees to the left
	stepper.step(512);
	delay(1000) ;
	// Rotate the motor 180 degrees to the right
	stepper.step(-1024);
	delay(1000) ;
	// Rotate the motor 270 degrees to the left
	stepper.step(1536);
	delay(1000) ;
	// Rotate the motor 360 degrees to the right
	stepper.step(-2048);
	delay(1000) ;
	}

view raw Stpper-1.ino hosted with ❤ by GitHub

	// Sample sketch for direct operation of stepping motor 28BYJ-48 and motor driver UKN2003A
	#define PIN_BLUE 7
	#define PIN_PINK 6
	#define PIN_YELLOW 5
	#define PIN_ORANGE 4

	// Defines 4 types of operation patterns to rotate the stepping motor clockwise
	static uint8_t Pattern0R[] = {2,0x08,0x02 } ;
	static uint8_t Pattern1R[] = {4,0x08,0x04,0x02,0x01 } ;
	static uint8_t Pattern2R[] = {4,0x0C,0x06,0x03,0x09 } ;
	static uint8_t Pattern3R[] = {8,0x08,0x0C,0x04,0x06,0x02,0x03,0x01,0x09 } ;

	// Defines 4 types of operation patterns to rotate the stepping motor to the left
	static uint8_t Pattern0L[] = {2,0x04,0x01 } ;
	static uint8_t Pattern1L[] = {4,0x01,0x02,0x04,0x08 } ;
	static uint8_t Pattern2L[] = {4,0x03,0x06,0x0C,0x09 } ;
	static uint8_t Pattern3L[] = {8,0x09,0x01,0x03,0x02,0x06,0x04,0x0C,0x08 } ;

	void setup() {
	pinMode(PIN_BLUE,OUTPUT) ;
	pinMode(PIN_PINK,OUTPUT) ;
	pinMode(PIN_YELLOW,OUTPUT) ;
	pinMode(PIN_ORANGE,OUTPUT) ;

	digitalWrite(PIN_BLUE,LOW) ;
	digitalWrite(PIN_PINK,LOW) ;
	digitalWrite(PIN_YELLOW,LOW) ;
	digitalWrite(PIN_ORANGE,LOW) ;
	}

	void stepMove(uint8_t *PTN,int STEPS,int SPEED) {
	int n = PTN[0] ;
	for (int r=0;r<STEPS;r++) {
	for (int i=1;i<=n;i++) {
	digitalWrite(PIN_BLUE,(((PTN[i] & 0x08) != 0) ? HIGH :LOW)) ;
	digitalWrite(PIN_PINK,(((PTN[i] & 0x04) != 0) ? HIGH :LOW)) ;
	digitalWrite(PIN_YELLOW,(((PTN[i] & 0x02) != 0) ? HIGH :LOW)) ;
	digitalWrite(PIN_ORANGE,(((PTN[i] & 0x01) != 0) ? HIGH :LOW)) ;
	delay(SPEED) ;
	}
	}
	}

	void loop() {
	// 1 rotation by changing the control pattern every 90 degrees
	stepMove(Pattern0R,128,25);
	delay(1000) ;
	stepMove(Pattern1R,128,10);
	delay(1000) ;
	stepMove(Pattern2R,128,5);
	delay(1000) ;
	stepMove(Pattern3R,128,1);
	delay(1000) ;

	// 1 rotation by changing the control pattern every 90 degrees
	stepMove(Pattern0L,128,25);
	delay(1000) ;
	stepMove(Pattern1L,128,10);
	delay(1000) ;
	stepMove(Pattern2L,128,5);
	delay(1000) ;
	stepMove(Pattern3L,128,1);
	delay(1000) ;
	}

view raw Stpper-2.ino hosted with ❤ by GitHub